tag:blogger.com,1999:blog-8260463056447598917.post8316361768737452427..comments2023-09-04T18:40:52.628+09:30Comments on Epsilon's Amiga Blog: Indivision ECS on Amiga 1000Epsilonhttp://www.blogger.com/profile/04050093693410409568noreply@blogger.comBlogger5125tag:blogger.com,1999:blog-8260463056447598917.post-69147578704554142592017-03-01T22:12:40.238+10:302017-03-01T22:12:40.238+10:30Hi, I am able to read and write german, here a rou...Hi, I am able to read and write german, here a rough translation for the german installation guide (I used as source the image above) :-)<br /><br />------------------------------------------------<br />Installation instructions:<br /><br />The Indivision ECS-Adapter for the Amiga 1000 is not, as one might think, put on the Denise socket, but on the Paula socket<br /><br />Please carefully remove the Paula chip and place it on the corresponding socket of the adapter<br /><br />Than install the adapter into the free Paula socket and the Indivision-ECS in the still free corresponding adapter socket<br /><br />Please leave the Denise in its socket. Also the socket on the Indivision-ECS, which is otherwise intended to use for the Denise, remains unused with this variant of installation<br />------------------------------------------------<br /><br />by the way great blog :-)<br /><br />greetings from germany (Dresden)Anonymoushttps://www.blogger.com/profile/10669953234446479323noreply@blogger.comtag:blogger.com,1999:blog-8260463056447598917.post-26400770559542284022016-04-28T16:16:41.024+09:302016-04-28T16:16:41.024+09:30amiga 1000 and microsoft mouse hahahahahaha uuuuuu...amiga 1000 and microsoft mouse hahahahahaha uuuuuuKarolhttps://www.blogger.com/profile/14341491170225639104noreply@blogger.comtag:blogger.com,1999:blog-8260463056447598917.post-75467422440873397602016-04-25T07:36:57.924+09:302016-04-25T07:36:57.924+09:30I believe you need a socket extender, so the Indiv...I believe you need a socket extender, so the Indivision ECS will be installed above the "piggy back" board. I haven't installed my Indivision ECS into one of my A1000's, but I think I remember getting such a socket extender when I purchased my Indivision ECS from AmigaKit, and indicated I would be installing it into an A1000.<br /><br />AmigaKit should be able to answer your questions, or contact Jens of Individual Computers directly, to see if he has the answer to your problem. Good Luck!anonymoushttps://www.blogger.com/profile/04712600457787485613noreply@blogger.comtag:blogger.com,1999:blog-8260463056447598917.post-89965445727648548582016-04-17T14:11:15.736+09:302016-04-17T14:11:15.736+09:30Im not sure if I am following 100% fully but if yo...Im not sure if I am following 100% fully but if you need more height, could you use a 48 pin IC socket as a spacer? - Aron GAron Goochhttps://www.blogger.com/profile/12016696181544026749noreply@blogger.comtag:blogger.com,1999:blog-8260463056447598917.post-79241629575958612302016-04-17T12:57:04.527+09:302016-04-17T12:57:04.527+09:30the adapter are only for none piggy-back.
ratte at...the adapter are only for none piggy-back.<br />ratte at a1k works on a dapter for piggy as i read this weekAnonymousnoreply@blogger.com